Street 2, Industrial Area, New Cairo 3 info@msquareeg.com العربية

Guide

How to Measure Windows and Doors for an Aluminium Quote

Measure width and height at three points each, write the smallest sizes in centimetres, add photos, and get an accurate first quote for windows and doors.

M-Square installers setting a large glass pane into a black aluminium storefront frame

Short answer: measure each opening’s width at the top, middle and bottom, and its height on the left, centre and right. Write down the smallest width and the smallest height in centimetres, as width × height, with the quantity. Add a photo of every opening and of the whole room or facade. This is enough for an accurate first quotation; final sizes are always confirmed on site before fabrication.

What you need

  • A steel tape measure (5 m or longer for doors and wide openings)
  • Your phone, for photos and notes
  • A simple list or sketch naming each opening, for example “Living room – window 1”

Step-by-step: measuring a window or door opening

  1. Measure the width three times: at the top, the middle and the bottom of the opening, from wall to wall (or from finished plaster to finished plaster).
  2. Measure the height three times: on the left, in the centre and on the right, from the sill or floor to the top of the opening.
  3. Keep the smallest numbers. Walls are rarely perfectly straight; the smallest size is the one that fits.
  4. Write sizes as width × height in centimetres, for example 240 × 160 cm, and note the quantity of identical openings.
  5. Check the diagonals on large openings. Measure from corner to corner both ways. If the two numbers differ by more than about 1 cm, the opening is out of square: mention it, our engineer will allow for it.
  6. Take photos. One straight-on photo of each opening, one showing the sill and top, and one of the whole room or facade.

Extra measurements for specific products

Product Also measure or note
Rolling shutters Space above the opening for the shutter box, inside or outside mounting, and whether you want manual or motorized operation
Shower cabins Width of each side, height to the ceiling or to the top of the tiles, and whether walls and floor are straight (the floor slope matters)
Glass handrails Length of each run, number of turns and landings, stair or slab edge type, and the floor finish (marble, porcelain, wood)
Partitions Floor-to-ceiling height at several points, wall-to-wall length, and where doors are needed
Blinds Inside the recess or over the opening, and the side where you want the control

Common measuring mistakes to avoid

  • Measuring before plaster or tiles are finished. Final finishes change the opening size. If work is still in progress, tell us the expected finish thickness.
  • Mixing millimetres and centimetres. Use centimetres everywhere, and write the unit.
  • Measuring the old window instead of the opening when replacing. Measure the masonry opening after noting how the old frame is fixed.
  • Rounding up. Always keep the smallest measurement.

Why final measurements are done on site

Your measurements are perfect for a first quotation and for choosing a system. Before anything is fabricated, an M-Square engineer measures every opening on site. This matters especially for tempered glass, which cannot be cut or drilled after tempering: every size and hole must be exact before production.

Frequently asked questions

Do I need exact measurements to get a quotation?

No. Approximate sizes in centimetres and a few photos are enough for a first quotation. Final measurements are taken on site by our engineer before fabrication.

Should I measure in millimetres or centimetres?

Centimetres are fine for a quotation. Write the unit next to every size to avoid mistakes.

What if my walls are not straight?

That is common. Take three widths and three heights, keep the smallest, and mention any slope or out-of-square corners. The engineer will plan the installation around them.

Can M-Square measure for me?

Yes. You can book a site visit through our quote form and our engineer will measure, check the site conditions and advise on the right system.

Need advice for your project?

Our technical office replies with honest recommendations and an itemised quotation, or visits to measure on site.